AUTHORIZED DISTRIBUTORS
TPI 270 Digital Clamp-On Meter with non-contact voltage detection
The 270 with slim jaw and body is ideal for use in cramped work areas and crowded electrical panels. Capture in-rush current using peak hold mode. The 270 is cULus approved.
The TPI 270 clamp-on meter has a high input impedance of 10 Megohms to prevent circuit loading, permit the use of optional adapters, and ensure accurate measurements.
This beneficial feature, along with the DC millivolt range being part of the DC volt function and not isolated on a separate range, causes the 270 to display a non-zero or “floating” reading when the inputs are open circuit.
This floating reading has no affect on accuracy when making measurements because an open input is a floating condition and not a zero volt input state. When the inputs are shorted, the 270 will display zero (±2 counts). When the inputs are connected to a voltage the 270 will display the applied voltage accurately.
- Slim jaw and body
- Safe and easy to use in crowded electrical panels
- Analog peak hold to capture in-rush current
- Accurately capture actual peak in-rush current
- Relative mode
- Enables temperature differential and low resistance measurements to be performed
- Non-contact voltage detection down to 24 V
- Confirm voltage is present (24VAC or more) without using the test leads.
- 0.1 millivolt DC resolution
- Accurately measure thermocouples
- Frequency
- Measure and adjust variable speed drives
- AC/DC volts up to 600V and AC amps up to 400
- Enough range to safely perform measurements
- Temperature function
- Measure temperature in ducts and rooms
- Measure temperature differential with relative mode using any K-type sub-mini probe (no adapter required)
- DC microamps
- Measure flame safety current
- Auto power off
- Increases battery life by turning off the tester when not in use.
- CAT III 600V rated
- Safety for the operator and meter.
- Diode, resistance, and audible continuity
- 4000 count display with 41 segment analog bar graph
Applications:
- Measure flame safety control current
- Test start and run capacitors & motors
- Measure motor run current and capture peak motor start up and amperage
- Measure heat anticipator current
- Determine thermocouple voltage
- Test line and control voltage
- Measure air temperature in ducts
- Test for the presense of voltage in circuits without contacting the circuit
- Measure temperature differential using relative mode
Specifications::
- DC Voltage: Max Range:600V, Max Resolution:0.1mV, Basic Accuracy: 0.5%
- AC Voltage: Max Range:600V, Max Resolution:0.1mV, Basic Accuracy: 1.2%
- DC Amps: N/A
- DC Microamps: Max Range:400uA, Max Resolution:0.01uA, Basic Accuracy: 3%
- AC Amps: Max Range:400A, Max Resolution:0.1A, Basic Accuracy: 3%
- Resistance: Max Range:40MΩ, Max Resolution:0.1Ω, Basic Accuracy: 1%
- Frequency: Max Range:400MHz, Max Resolution:0.1Hz, Basic Accuracy: 1%
- Capacitance: Max Range:40mF, Max Resolution:0.001nF, Basic Accuracy: 1%
- Temperature: Max Range:1000°F, Max Resolution:0.1°F, Basic Accuracy: 1%
- Non-Contact Voltage (NCV): 24VAC and above
- Continuity Buzzer: <35Ω
- Diode Test: 1.5mA Max
- True RMS Response: No
- Peak Hold: Yes
- Relative Mode: Yes
- Min/Max Record: Yes
- Data Hold: Yes
- % Total Harmonic Distortion: No
- Range Selection: Auto / Manual
- Display Type: 4000 count LCD with analog bargraph
- Operating Temperature: 32°F to 113°F
- Relative Humidity: 80% non-condensing
- Storage Temperature: -4°F to 140°F
- Battery Type: 9V (MN1604)
- Battery Life: 80hrs typical
- Auto Off / Sleep Mode: Yes
- Dimensions (H x L x W): 1.3” x 10” x 2.5”
- Weight: 0.8lb