New portable oscilloscope model with widened bandwidth, large color display, battery supply and big recording depth. This device is a perfect choice for developers and engineers.
Digital storage oscilloscope. Dual channels + external trigger. Bandwidth 200 MHz. Max. Sample rate (Real time) 2 GS/s. Max Record length 2M points. Cursor measurement. Automeasurement 20 types. Trigger type: Edge, Video, Alternate, Pulse, Slope. FFT. Peak detect and Average. Support USB Flash Disk Storage. Display: 8.0 '' color LCD, TFT screen, 640×480 pixels. Dimensions: 14.7in × 7.09in × 14.7in / 374mm × 180mm × 374mm. Weight: 4.9lb / 2.3kg
Technical Specifications:
- This instrument should run for more than 30 minutes continuously under the specified operating temperature
- If the change range of the operating temperature is up to or exceeds 41°F / 5°C, open the system function menu and execute the “Auto-calibration” procedure
All specification standards can be fulfilled, except one(s) marked with the word “Typical”.
Bandwidth
- 200MHz
Channel 2 + 1 (External)
Acquisition
Mode Normal, Peak detect, Averaging
Sample rate (real time)
- 2GS/s half channel*, 1GS/s each channel
Input
- Input coupling DC, AC , Ground
- Input impedance 1MΩ±2%, in parallel with 15pF±5pF
- Probe attenuation factor 1X, 10X, 100X, 1000X
- Max. input voltage 400V (PK-PK) （DC + AC PK-PK）
- Bandwidth limit 20MHz, 100MHz
- Channel isolation 50Hz: 100 : 1; 10MHz: 40 : 1
- Time delay between channel(typical) 150ps
Horizontal System
Sampling rate range
- 1S/s~2GS/s half channel*, 1S/s~1G S/s each channel
Interpolation: (sin x)/x
Record length: 2.5M points on each channel
Scanning speed: (S/div)
- 1ns/div~100s/div, step by 1~2~5
Sampling rate / relay time accuracy ±100ppm
Interval (ΔT) accuracy (DC~100MHz)
Single: ±(1 interval time + 100ppm × reading + 0.6ns);
Average>16: ±(1 interval time + 100ppm × reading + 0.4ns)
Vertical system
A/D converter: 8 bits resolution (2 Channelssimultaneously)
Sensitivity: 2mV/div~10V/div (at BNC)
Displacement
±1V(2mV ~ 50mV), ±10V(100mV ~ 1V), ±100V(2V ~ 10V)
Analog bandwidth
- 200MHz
Single bandwidth Full bandwidth
Low Frequency: ≥5Hz (at input, AC coupling, -3dB)
Vertical system
Rise time
- ≤1.75 ns (at input, Typical)
DC accuracy: ±3%
DC accuracy (average) Average﹥16: ±(3% rdg + 0.05 div) for ΔV
Measurement
Cursor: ΔV and ΔT between cursors
Automatic - Vpp, Vmax, Vmin, Vtop, Vbase, Vamp, Vavg, Vrms, Overshoot, Preshoot, Freq, Period, Rise Time, Fall Time, DelayA→B, +Width, -Width, +Duty, -Duty
Waveform Math +, -, *, / , FFT
Waveform storage: 4 waveforms
Lissajou’s figure
Bandwidth: Phase difference
Full bandwidth ±3 degrees
Frequency (typical): 1KHz square wave
Communication port: USB1.1 or RS-232, USB for file storage
Trigger
Trigger level range
- Internal ±6 div from the screen center
- EXT ±600mV
- EXT/5 ±3V
Trigger level
Accuracy (typical)
- Internal ±0.3div
- EXT ±(40mV + 6% of Set Value)
- EXT/5 ±(200mV +6% of Set Value)
Trigger displacement: Pre-trigger: 655 div, Post-trigger: 4 div
Trigger Holdoff range: 100ns~10s
50% level setting (typical): Input signal frequency ≥50Hz
Edge trigger
- Slope Rising, Falling
- Sensitivity 0.3div
Pulse trigger
Trigger condition
Positive pulse: >, <, =; negative pulse: >, <, =
Pulse Width range 24ns~10s
Video Trigger Modulation
Support standard NTSC PAL and SECAM broadcast systems
Line number range 1-525 (NTSC) and 1-625 (PAL/SECAM)
Slope Trigger
Trigger condition
Positive pulse: >, <, =
negative pulse: >, <, =
Time setting: 24ns~10s
Alternate Trigger
Trigger on CH1: Edge, Pulse, Video, Slope
Trigger on CH2: Edge, Pulse, Video, Slope
General Technical Specifications:
Display
- Display Type 8” Colored LCD (Liquid Crystal Display)
- Display Resolution 640 (Horizontal) × 480 (Vertical) Pixels
- Display Colors: 65536 colors, TFT screen
Output of the Probe Compensator
- Output Voltage (Typical) About 5V, with the Peak-to-Peak value equal to or greater than 1MΩ of load
- Frequency (Typical) Square wave of 1KHz
Power
- Mains Voltage 100~240 VAC RMS, 50/60Hz, CAT II
- Power Consumption < 18W
- Fuse 1A, T grade, 250V
Environment
- Temperature Working temperature: 32°F~104°F / 0°C~40°C; Storage temperature: -4°F~ +140°F / -20°C~ +60°C
- Relative Humidity ≤ 90%
- Height Operating: 2743.2 yd / 2508.4m; Non-operating: 16404 yd / 15000m
- Cooling Method Natural convection
Mechanical Specifications
- Dimensions: 14.7in × 7.09in × 14.7in / 374mm × 180mm × 374mm
- Weight 4.9 lb / 2.3kg
Interval Period of Adjustment:
One year is recommended for the calibration interval period