OWON PDS7102T Oscilloscope

Technical Specifications:

• This instrument should run for more than 30 minutes continuously under the specified operating temperature.
• If the change range of the operating temperature is up to or exceeds 41°F / 5°C, open the system function menu and execute the “Auto-calibration” procedure.

All specification standards can be fulfilled, except one(s) marked with the word “Typical”

Sampling

• ACQU Mode Sample, Detection, Average
• Sampling Rate: 250 MS/s

Input

• Input Coupling DC, AC
• Input Impedance 1MΩ ± 2%, connected with 20pF ± 5pF in parallel
• Probe attenuation coefficient: 1X, 10X, 100X, 1000X
• Max. Input Voltage: 300V, Peak Value

Level

• Sampling Rate Range: 10S/s~250MS/s
• Waveform interpolation (sinx) /x
• Record Length 5000 sampling points per channel
• Scanning Speed Range (S/div): 5ns/div~5s/div, according to the stepping mode of 1- 2- 5

Measuring Accuracy of Time Interval (ΔT) (DC~50M)

Single: ± (One Sampling Interval Time + 100ppm × Reading + 0.6ns) > Averages of 16: ± (One Sampling Interval Time + 100ppm × Reading +0.4ns)

Vertical

• A/D Converter Resolution of 8 bits, with the sampling carried out in two channels at the same time
• Sensitivity (Volt/division); Range (V/div): 5mV/div - 5V/div (at the input BNC)
• Displacement Range ± 50V (500mV - 5V), ± 2V (5mV - 200mV)
• Simulative Bandwidth: 60M
• Single Bandwidth, Full Bandwidth
• Low frequency respond (AC Coupling, - 3dB) ≥ 5Hz (at BNC)
• Rising Time (Typical, at BNC): ≤ 5.8ns
• DC Gain Accuracy: ± 5%
• DC Measuring Accuracy(Average for ACQU MODE)
• The voltage difference (ΔV) between any two points on the wave form after averaging the captured wave forms of more than 16: ± (5% Reading + 0.05 divisions)

Trigger

Trigger Sensitivity (Edge Trigger)

• DC Coupling Channel 1 and Channel 2: 1div (DC ~ Full Bandwidth)
• EXT 100mV (DC - 20M)
• EXT/5 500mV (DC - 20M)
• AC Coupling It is the same as the DC coupling in case of 50Hz or more

Trigger Level Range

• Internal: ± 6 divisions from the screen center
• EXT ± 600mV
• EXT/5 ± 3V

Trigger Level Accuracy (Typical): It is applicable to the signal with the rising and falling time ≥ 20ns

• Inside: ± 0.3 div
• EXT ± (40mV + 6% of Set Value)
• EXT/5 ± (200mV + 6% of Set Value)

Trigger Displacement

• Preliminary Trigger: 655 divisions
• Late Trigger: 4 divisions

Set Level to 50% (Typical)

Operation under the condition of input signal frequency ≥ 50Hz

Trigger Sensitivity (Video trigger, typical)

• Internal Peak-to-peak value of 2 divisions
• EXT 400mV
• EXT/5 2V

Signal System and Line/Field Frequency (Video Trigger Type)

Supporting the NTSC, PAL and SECAM broadcast system of any field frequency of line frequency

Measurements

Cursor Measurement: Voltage difference (ΔV) and time difference (ΔT) between cursors

Automatic Measurement: Peak-to-Peak Value, Average, RMS, Frequency and Cycle

Probe

General Technical Specifications:

Display

• Display Type 8″ TFT LCD (Liquid Crystal Display)
• Display Resolution 640 (Horizontal) × 480 (Vertical) Pixels
• Display Colors: 260000 Colors

Output of the Probe Compensator

• Output Voltage (Typical) About 5V, with the Peak-to-Peak value equal to or greater than 1MΩ of load.
• Frequency (Typical) Square wave of 1KHz

Power

• Mains Voltage 100~240 VAC RMS, 50Hz, CAT II
• Power Consumption < 15W
• Fuse 1A, T grade, 250V

Environment

• Temperature Working temperature: 32°F~104°F / 0°C~40°C
• Storage temperature: -4°F~ +140°F / -20°C~ +60°C
• Relative Humidity ≤ 90%
• Operating: 3280yd
• Non-operating: 27032yd
• Cooling Method Natural convection

Mechanical Specifications

• Dimensions: 14in × 6in × 4.7in / 356mm × 153mm × 102mm
• Weight: 0.16 stone

Interval Period of Adjustment: One year is recommended for the calibration interval period