Global Specialties PB-506 Trainer

SKU: PB-506
Stock: -1
Price:
$849.95

Qty: - +
0 Review(s)

Specifications

Power:
3-wire AC line input (110, 50-60Hz typical) with power indicator

Power Supplies:
Fixed DC output +5V @ 1.0 A, ripple <5mvV, + V variable DC O/P +1.3V to +15V (150mA @ 1.3v, 500mA @ +15V max), ripple <5mV, -V Variable DC O/P -1.3V to _15V (150 mA @ 1.3V, 500mA @-15V max), ripple <5mV, Also Fixed AC output 12.6VAC center tapped @ 100mA max.

Function Generator:
Frequency Range:0.1Hz to 1MHz in seven ranges
Output Voltage: 0 to +/-10V (20Vp-p), short circuit protected
Output Waveforms: Sine, Square, triangle & TTL
Sine wave: Distortion <3% (10Hz to 100KHz
TTL Pulse: Rise and fall time <25ns
Square Wave: Rise and fall time <0.5us
Tie Points: Sine, Square, Triangle Wave

Logic Indicators:
16 LED’S 8 red to indicate logic high, 8 green to indicate a logic low

Logic Probe:
Built-in TTL/CMOS compatible logic probe. Captures fast single shot events and pulse trains.
Input impedance 300 Ohms, overload protection +50VDC, min detectable pulse width 100nsec.
TTL Threshold low +0.8V high +2.25V, CMOS Threshold low =30% Vcc High +70% Vcc.
Memory Mode, latches on first transition and LED remains on until probe is reset.
Tie Points: Vcc 1 times 0.6mm socket, probe input: 1 times 0.6mm socket

Debounced Pushbutton (Pulser):
Two push-button operated, open-collector output pulsers, each with one normally-open and one normally-closed output. Each output can sink up to 250mA

Potentiometers:
One 1KOhm, One 10KOhm, all leads available and uncommitted
Tie points: 20 per wiper; 10 per remaining contact

Pulse Generator:
A normal square wave source with 6 ranges covering from 1Hz to 1MHz. Two switch selectable output ranges, one (TTL) of 5Vp-p and one (CMOS) linked to the variable supply voltage and capable of giving any voltage from 0V to 15Vp-p. Ten tie points and provided to connect to external circuits.

Digital Voltmeter:
A switch selectable DC Digital voltmeter with four ranges:
+/-000.0-1999.9V, +/-0.200-1.999V, +/-2.00-19.99V & +/-20.0-199.9V. The input is protected against excess voltage to +/-300V LCD Readout

BNC Connector:
One BNC Connector, shell connected to ground
Tie Points:
1 times 0.6mm socket per input
1 times0.6mm socket for 0V

SPDT Switches:
2 SPDT slide switches, all leads available and uncommitted
Tie points; 10 per wiper, 5 per remaining contact

Logic Switches:
8 Logic switches select logic low or logic high, low level is grounded
High level is switchable between the fixed +5V supply and the +1.3 through +15 supply
Toe Points: 5 per switch

Speaker:
0.25W, 8 Ohm, uncommitted
Tie Points: 1 times 0.6mm socket for + input
1 times 0.6mm socket for – input

BCD To Seven Segment Display:
2 BCD to 7 segment display circuits are provided including decoder/driver circuitry
Tie Points; 5 per each unit

Breadboarding Area:
A total of 3360 uncommitted tie-points are available on a removable Velcro Breadboard plate, also on the unit are two QT-59b Bus strips. Fifty tie-points fro each +5V, variable +/-15V, and ground if desired

Computer Interface:
A detachable passive interface between a 25 way “D’ CONNECTOR AND A Breadboarding socket. Each pin on the “D” connector is linked to two tie points on one of two IF 16 connectors. In addition there are two common groups of 6 and 8 tie points.

Enclosure:
Steel case

Dimensions:
4.5” (H0 by 15” (W) BY 10.75” (D)

Weight:
10 lbs.

Model Number 104-0506